New Products

Monument Autocut Pipe Cutter - 28mm

Monument's Autocut Pipe Cutter has a compact design that is easy to carry from job to job and is ideal for use in confined places. Ideal for plumbers cutting copper piping for heating systems, with a single action automatic tube cut this handy pipe cutter with its twist and cut action cuts copper with only a few turns. Made from metal with a comfortable ergonomic grip to make cutting copper quick and easy. A replaceable cutter wheel is included and a ratchet handle can be purchased separately if required.

Was: £26.95Save: £7.00 (26%)

Now: £19.95

In Stock

Draper D987 Box Section Spirit Level - 120cm/48"

The Draper D987 Box Section Spirit Level is made from extruded aluminium and features reinforcement ribs that also make the level easier to handle. Along the bottom side of the level is a milled measuring surface that ensures the level rests flat against surfaces. There are also two rubber grip holes to make the level quick and easy to position. This level features solid acrylic vials, with twin vertical vials to ensure more accurate measuring as well as a single horizontal vial. The horizontal vial can also be used for overhead measurements by turning the level upside down. Each of the plastic end caps has a hanging tab to allow the level to be stored more easily.

Was: £37.06Save: £17.11 (46%)

Now: £19.95

In Stock

Draper D786 Box Section Spirit Level - 60cm/24"

The Draper D986 Box Section Spirit Level is made from extruded aluminium and features reinforcement ribs that also make the level easier to handle. Along the bottom side of the level is a milled measuring surface that ensures the level rests flat against surfaces. This level features solid acrylic vials, with twin vertical vials to ensure more accurate measuring as well as a single horizontal vial. The horizontal vial can also be used for overhead measurements by turning the level upside down. The level has fixed plastic end caps, plus hanging tabs to allow the level to be stored more easily.

Was: £13.97Save: £6.02 (43%)

Now: £7.95

In Stock

Draper D786 Box Section Spirit Level -30cm/12"

The Draper D986 Box Section Spirit Level is made from extruded aluminium and features reinforcement ribs that also make the level easier to handle. Along the bottom side of the level is a milled measuring surface that ensures the level rests flat against surfaces. This level features solid acrylic vials, with one vertical vials and a one horizontal vial. The horizontal vial can also be used for overhead measurements by turning the level upside down. The level has fixed plastic end caps, plus hanging tabs to allow the level to be stored more easily.

Was: £10.51Save: £4.56 (43%)

Now: £5.95

In Stock

Wiha 2pc slimFix VDE Screwdriver Set Slotted & Pozi Terminal

The Wiha 2pc slimFix VDE Screwdriver Set Slotted & Pozi Terminal is an innovative solution to a commonly occurring problem for electricians. With many VDE screwdrivers, the insulation often obstructs and prevents access to low-lying fastening elements. The slimFix system combats this by reducing the diameter of the blade by 33%, allowing access to low-lying fasteners and spring clips. This is achieved by spraying a protective insulation directly onto the end of the blade and completely integrating the insulation into the lower blade area. Each blade is made from chrome-vanadium-molybdenum steel with a hardened black finish. Wiha's SoftFinish multi-component handle provides a secure, comfortable grip and has roll-off protection to prevent the screwdriver from rolling away when put down. The set contains 2 SlimFix screwdrivers: 3.5 x 0.6mm Slotted x 100mm long Slotted/Pozi No 2 For Terminal Screws x 100mm long.

Was: £26.76Save: £11.81 (44%)

Now: £14.95

In Stock

Wiha 2pc slimFix VDE Screwdriver Set Slotted & Pozi

The Wiha 2pc slimFix VDE Screwdriver Set Slotted & Pozi is an innovative solution to a commonly occurring problem for electricians. With many VDE screwdrivers, the insulation often obstructs and prevents access to low-lying fastening elements. The slimFix system combats this by reducing the diameter of the blade by 33%, allowing access to low-lying fasteners and spring clips. This is achieved by spraying a protective insulation directly onto the end of the blade and completely integrating the insulation into the lower blade area. Each blade is made from chrome-vanadium-molybdenum steel with a hardened black finish. Wiha's SoftFinish multi-component handle provides a secure, comfortable grip and has roll-off protection to prevent the screwdriver from rolling away when put down. The set contains 2 SlimFix screwdrivers: 3.5 x 0.6mm Slotted x 100mm long No 2 Pozi x 100mm long.

Was: £24.60Save: £10.65 (43%)

Now: £13.95

In Stock

Nextorch Cliplite LED Light

The Nextorch Cliplite LED Light is a versatile and compact clip on light that is great for everyday use, leaving both hands free for the job. With two LED's, the light has 3 modes Single, Dual, and Strobe. Powered by 2 CR2032 button cells, the light has a run time of up to 50 hours, with an output of 8 lumens in single mode and 16 lumens in dual mode. Light can be directed exactly where it is needed thanks to a 180 degree rotating arm and LED lens, plus the 360 degree rotating clip that can be attached to almost anything. A useful "Auto-Off" feature turns the light off after 10 minutes of continuous use to preserve the battery life. For peace of mind every Nextorch product comes with a 3 year warranty.

Was: £19.96Save: £2.01 (10%)

Now: £17.95

In Stock

Nextorch K3 LED Pen Light with Clip

The Nextorch K3 LED Pen Light with Clip is a compact, lightweight pocket light for everyday use. A super bright LED provides a maximum output of 180 lumens over a distance of 56.5m, with a maximum run time of 38 hours at maximum output. The torch is powered by 2x AAA batteries (included) and there are 4 modes - High, Medium, Low, and Strobe. The body has a sleek and modern design, is easy to hold and has a useful stainless steel clip. It is also impact resistant to 1 metre and has IPX-4 water resistance. A spare set of AAA batteries is also included with this torch. For peace of mind every Nextorch product comes with a 3 year warranty.

Was: £29.95Save: £4.00 (13%)

Now: £25.95

In Stock

Nextorch K2 Key Ring LED Torch with Clip

The Nextorch K2 Key Ring LED Torch with Clip is a light and compact flashlight for everyday use. With an aerospace grade aluminium and stainless steel body, the torch has super bright LED providing an output of 7 lumens, 30 lumens or 65 lumens. Powered by a single AA battery (included) the runtimes are 90 minutes at 65 lumens, 270 minutes at 30 lumens and 900 minutes at 7 lumens. The body has an anti-rolling structure, is impact resistant to 1 metre and has IPX-4 water resistance. A twist on/off switch allows one of the 4 modes to be selected High, Medium, Low, and Strobe. For peace of mind every Nextorch product comes with a 3 year warranty.

Was: £24.95Save: £3.00 (12%)

Now: £21.95

In Stock

Nextorch K1 Key Ring LED Torch

The Nextorch K1 Key Ring LED Torch is a light and compact flashlight for everyday use. With an aerospace grade aluminium and stainless steel body, the torch has a SSCP9 LED chip to provide a minimum output of 15 lumens over a distance of 30m. Powered by a single AAA battery (included) the minimum run time at maximum output is 100 minutes. The body has an anti-rolling structure, is impact resistant to 1 metre and has IPX-4 water resistance. A twist on/off switch allows one of the 4 modes to be selected High, Medium, Low, and Strobe. For peace of mind every Nextorch product comes with a 3 year warranty.

Was: £14.95Save: £5.00 (33%)

Now: £9.95

In Stock

Nextorch Viker Star Multi-Function LED Head Torch

The Nextorch Viker Star Multi-Function LED Head Torch is a high output LED headlamp ideal for a wide range of activities, both at work and during leisure pursuits. The CREE LED provides a super bright beam with a maximum output of 140 lumens over a distance of 110m. The head lamp has 3 modes High, Low, and SOS which can be quickly selected using the water resistant magnetic control switch. Powered by 3 AA batteries which are included, the runtime is 25 hours on high and 100 hours on low. This compact and lightweight design has an adjustable headband for improved comfort, while the light itself has a 90 degree angle adjustment for multi-direction lighting. For peace of mind every Nextorch product comes with a 3 year warranty.

Was: £29.95Save: £4.00 (13%)

Now: £25.95

In Stock

Nextorch myTorch Rechargable Professional LED Torch

The Nextorch myTorch Rechargeable Professional LED Torch is an extremely versatile flashlight suitable for a wide range of activities, both at work and during leisure pursuits. At the heart of the torch is a CREE LED that provides a super bright beam with a maximum output of 200 lumens that is both long and wide over a distance of 200m. A rechargeable battery and USB cable are included to allow the battery to be recharged, while the torch has built-in over-charge/discharge protection and reverse polarity protection circuits. Made from aerospace grade 6061-T6 grade aluminium, the torch has a hard-anodized anti-abrasive finish, is impact resistant up to 1 metre and has IPX-7 waterproofing (up to 1 metre). Ready to use straight out of the box, the torch is pre-set with 3 modes - High, Low, and Strobe for the most common applications. However the flashlight is also fully customisable by connecting the torch to a PC using the USB cable and running the myTorch Tuner software. With just a few clicks the torch can be programmed to your exact requirements, adjusting the luminance and frequency, with the option to replace any of the 3 pre-set modes with your custom program. For peace of mind every Nextorch product comes with a 3 year warranty.

Was: £79.96Save: £10.01 (13%)

Now: £69.95

In Stock

Nextorch myTorch Professional LED Torch (3AA)

The Nextorch myTorch Professional LED Torch (3AA) is an extremely versatile flashlight suitable for a wide range of activities, both at work and during leisure pursuits. At the heart of the torch is a CREE LED that provides a super bright beam with a maximum output of 150 lumens that is both long and wide over a distance of 170m. Three AA batteries are included and the torch has a minimum run-time of 330 minutes at maximum output. The torch is impact resistant up to 1 metre and has IPX-7 waterproofing (up to 1 metre). Made from aerospace grade 6061-T6 grade aluminium, the torch has a hard-anodized anti-abrasive finish. Ready to use straight out of the box, the torch is pre-set with 3 modes - High, Low, and Strobe for the most common applications. However the flashlight is also fully customisable by connecting the torch to a PC using the included USB cable and running the myTorch Tuner software. With just a few clicks the torch can be programmed to your exact requirements, adjusting the luminance and frequency, with the option to replace any of the 3 pre-set modes with your custom program. For peace of mind every Nextorch product comes with a 3 year warranty.

Was: £39.95Save: £5.00 (13%)

Now: £34.95

In Stock

Nextorch myTorch Professional LED Torch (2AA)

The Nextorch myTorch Professional LED Torch (2AA) is an extremely versatile flashlight suitable for a wide range of activities, both at work and during leisure pursuits. At the heart of the torch is a CREE LED that provides a super bright beam with a maximum output of 140 lumens that is both long and wide over a distance of 110m. Two AA batteries are included and the torch has a minimum run-time of 100 minutes at maximum output. The torch is impact resistant up to 1 metre and has IPX-7 waterproofing (up to 1 metre). Made from aerospace grade 6061-T6 grade aluminium, the torch has a hard-anodized anti-abrasive finish. Ready to use straight out of the box, the torch is pre-set with 3 modes - High, Low, and Strobe for the most common applications. However the flashlight is also fully customisable by connecting the torch to a PC using the included USB cable and running the myTorch Tuner software. With just a few clicks the torch can be programmed to your exact requirements, adjusting the luminance and frequency, with the option to replace any of the 3 pre-set modes with your custom program. For peace of mind every Nextorch product comes with a 3 year warranty.

Was: £32.95Save: £4.00 (12%)

Now: £28.95

In Stock

Sigma 5 STANDARD SERIES Tile Cutter - 50cm Cut Length

The Sigma 5 STANDARD SERIES Tile Cutter is a compact tile cutter suitable for cutting a range of tiles up to 16mm thick. Complete with a tungsten carbide scoring wheel, the tile is scored by pulling the breaker along the surface of the tile. Pushing the breaker handle downwards quickly breaks the tile while the sprung-loaded base plates absorb the impact. The swivelling support bar attaches to the fixed measurement bar and rotates between 0 - 60 degrees to determine the angle of cut. There is also a fixed measurement bar that has a scale in centimetres, allowing the length of tile to be measured from the centre of the cutting line. With a weight of 7.2kg, the maximum straight cut length is 50cm and diagonal cuts can be made on tiles measuring up to 35x35cm.

Was: £212.40Save: £12.45 (6%)

Now: £199.95

In Stock

Irwin Vise-Grip Fast Release Locking Pliers Curved Jaw - 10"

From the inventors of the world's first locking pliers, Irwin's Fast Release Locking Pliers With Curved Jaw are ideal for gripping nut or bolt heads, with a self-energising lower jaw that provides 3x more gripping power compared to regular locking pliers. The pliers are twice as easy to open as regular locking pliers thanks to the Irwin Fast Release handle that allows for quick one handed operation. To provide improved comfort, control and less hand fatigue, the handles are covered in Irwin's anti-pinch, non-slip ProTouch rubber grip. The jaw mechanism is designed to provide maximum torque without slipping or stripping, gripping tighter as more torque is applied without requiring heavy input pressure. Hardened teeth grip from any angle and the curved jaw transfers great pressure on four points of a nut or bolt head, for any job needing maximum torque. A hex key adjustment screw can be tightened to adjust the jaw pressure and draw materials together, whilst providing a controlled release. Size - 10" / 250 mm Jaw Capacity 1-7/8" / 48 mm

Now: £13.95

In Stock

Irwin Vise-Grip Groove Lock Pliers - 10"

Irwin Vise-Grip Groove Lock Pliers provide an all-purpose grip on round, hex, square and flat surfaces making them ideal for any tradesman. Each precision part that goes into the pliers is made using a Metal Injection Moulding process, ensuring high strength, outstanding performance and a finished plier that is extremely durable. The lower jaws adjust twice as fast as traditional groove lock pliers using the press-n-slide button adjustment. The Multi-Groove ratcheting system has twice the number of groove positions than traditional designs allowing for precise jaw positioning when gripping any surface, while also delivering optimal hand positioning. Right Angled teeth provide grip in all directions for maximum bite on the work piece. To provide improved comfort, control and less hand fatigue, the handles are covered in Irwin's anti-pinch, non-slip ProTouch rubber grip. Size - 10" / 250 mm Jaw Capacity 2 1/4" / 48 mm Groove Positions 16 Pipe Size 1 1/2" Nut Size (Across Flats 40mm)

Now: £15.95

In Stock

Irwin Vise-Grip Fast Release Locking C-Clamp Regular Tips - 6"

From the inventors of the world's first locking pliers, the Irwin Vise-Grip Fast Release Locking C-Clamp With Regular Tips has wide opening 'C' jaws that provide versatile clamping for a variety of materials. The clamp is twice as easy to open as regular clamps thanks to the Irwin Fast Release handle that allows for quick one handed operation. A high-grade, heat-treated alloy steel construction provides improved durability and the handles are coated with an ergonomic rubber grip for improved comfort. A turn screw on the handle quickly adjusts the pressure and fit of the jaws to suit the materials being clamped, whilst also making the clamp ideal for repetitive use. Even large, long reach materials can be clamped in the required position thanks to the wide opening jaws, making this clamp ideal for applications such as sheet metal work and welding. Size - 6" / 150 mm Jaw Capacity 2 1/8" / 54mm

Now: £12.95

In Stock

Irwin Vise-Grip Locking C-Clamp Swivel Pads - 6"

From the inventors of the world's first locking pliers, the Irwin Vise-Grip Locking C-Clamp With Swivel Pads has wide opening 'C' jaws that provide versatile clamping for a variety of shapes. The high-grade, heat-treated alloy steel construction provides greater durability, while the classic trigger jaw release ensures maximum locking force. A turn screw on the handle quickly adjusts the pressure and fit of the jaws to suit the materials being clamped, whilst also making the clamp ideal for repetitive use. Even large, long reach materials can be clamped in the required position thanks to the wide opening jaws, making this clamp ideal for applications such as sheet metal work and welding. This version has swivel pads allowing the clamp to be used with tapered work pieces, in awkward fabricating jobs, or when delicate items need to be clamped without damaging the work surface. Size - 6" / 150 mm Jaw Capacity 2 1/8" / 54mm

Now: £11.95

In Stock

Irwin Vise-Grip Original Locking Pliers Curved Jaw - 10"

From the inventors of the world's first locking pliers, Irwin's Vise-Grip Original Locking Pliers With Curved Jaw are ideal for gripping nut or bolt heads, with a self-energising lower jaw that provides 3x more gripping power compared to regular locking pliers. Hardened teeth grip from any angle and the curved jaw transfers great pressure on four points of a nut or bolt head, for any job needing maximum torque. A classic trigger release ensures maximum locking force while the jaw mechanism provides maximum torque without slipping or stripping, gripping tighter as more torque is applied without requiring heavy input pressure. The hex key adjustment screw can be tightened to adjust the jaw pressure and draw materials together, whilst providing a controlled release. Size - 10" / 250 mm Jaw Capacity 1-7/8" / 48 mm

Now: £11.95

In Stock